[Molding matrix formulation of hot-melt pressure-sensitive adhesive plaster of personalized traditional Chinese medicine preparations].

This study aims to optimize the matrix formulation for the hot-melt pressure-sensitive adhesive plaster of personalized traditional Chinese medicine(TCM) preparations and verify the applicability of the formulation. The central composite design in JMP Pro 16.1.0 was employed to optimize the dosages of styrene-isoprene-styrene triblock copolymer(SIS), hydrogenated petroleum resin, and lightweight liquid paraffin, with the fine powder of Yipifang as the model drug(drug loading of 10%) and the sensory score and objective evaluation as the comprehensive evaluation indicators. The quality evaluation system of hot-melt pressure-sensitive adhesive plaster of personalized TCM preparations was established. The applicability of the optimized matrix formulation of hot-melt pressure-sensitive adhesive plaster was verified with 16 TCM preparations for external application. Furthermore, the applicability of the matrix formulation was investigated with different drug loadings. The general molding matrix formulation was SIS∶hydrogenated petroleum resin∶lightweight liquid paraffin 3∶3∶5. The optimized matrix formulation showed good molding properties and high quality scores for 16 TCM preparations and were suitable for the plastering of finely powdered decoction pieces with a loading capacity of 10% to 30%. The results suggest that the optimized matrix formulation has good applicability and is suitable for TCM preparations. The findings lay a foundation for the application and promotion of the hot-melt pressure-sensitive adhesive plasters of personalized TCM preparations.

Comparative study on alginate/chitosan microcapsules and Montanide ISA 61 as vaccine adjuvants in mice.

Selection of adjuvant to be combined with the antigen is an extremely important point for formulating effective vaccines. The aim of this study was to evaluate reactogenicity, levels of IgM, IgG and subclasses (IgG1, IgG2b and IgG3), and protection elicited by vaccine formulations with association of chitosan coated alginate or Montanide ISA 61 with γ-irradiated Brucella ovis. The alginate/chitosan biopolymers as well as the Montanide ISA 61 emulsion elicited intense and long-lasting local response, especially when associated with the antigen. However, Montanide ISA 61 induced less intense reactogenicity when compared to alginate/chitosan. Furthermore, γ-irradiated B. ovis with Montanide ISA 61 induced higher levels of IgG2b an important marker of cellular immune response. In conclusion, Montanide ISA 61 resulted in milder reactogenicity when compared to the alginate/chitosan, while it induced a high IgG2b/IgG1 ratio compatible with a Th1 profile response.

Cadaver preservative properties of a solution composed of honey, ethyl alcohol, liquid paraffin, distilled water and citric acid: Experiments on rabbit cadavers.

The objective of this study is to assess the efficacy of a solution including honey, ethyl alcohol, liquid paraffin, distilled water and citric acid (HEFS) as a preservative for rabbit cadavers, serving as a potential substitute for formaldehyde. The cadavers underwent preservation using three distinct solutions: 10% formalin, 35% alcohol and HEFS. The cadavers were subjected to a total of four sampling events, occurring at 4-month intervals, in order to collect specimens for microanatomical, histological, microbiological, mycological, colourimetric, texture and odour analysis. In terms of hardness, suitability for dissection and joint mobility metrics, the cadavers fixed with HEFS had superior qualities to those fixed with formalin. The fixation quality of HEFS for histological analyses was deemed acceptable, except kidney and intestinal tissues. In texture analysis, differences only in the elasticity parameter (p < 0.05) in the same sampling period. A total of 10 (13.9) bacteria isolates were identified among which, Metasolibacillus meyeri 3 (30%) was predominantly followed by Staphylococcus aureus 2 (20%), Bacillus siamensis, Bacillus subtilis, Pseudarthrobacter oxydans, Bacillus licheniformis, Bacillus subtilis subsp. subtilis with a proportion of 1 (10%), respectively, by both microbiological and molecular analysis. However, no anaerobic bacteria and fungi were isolated. A considerable percentage of the students had the perception that HEFS was appropriate for utilization in laboratory settings due to its absence of unpleasant odours and detrimental impact on ocular and respiratory functions. In conclusion, we consider that HEFS may serve as a viable substitute for formalin solution in the preservation of rabbit cadavers.

Lipoid pneumonia induced by aspiration of liquid paraffin.

INTRODUCTION: This case report describes a case of exogenous lipoid pneumonia (ELP) resulting from the inhalation of a lipoid substance. Lipoid pneumonia, also known as cholesterol pneumonia or golden pneumonia, is an uncommon inflammatory lung disease characterized by the presence of lipid-laden macrophages in the alveolar walls and lung interstitial tissue. Exogenous lipoid pneumonia occurs when substances containing lipids enter the airways through aspiration or inhalation, triggering an inflammatory response. CASE REPORT: The patient in this case study was an 83-year-old woman with hypertension and diabetes mellitus who had been using paraffin oil as a mouthwash for an extended period. The diagnosis of exogenous lipoid pneumonia was established based on the patient's history of exposure to liquid paraffin oil, typical radiological findings, and histopathological examination.

Adjuvant screening of the Senecavirus A inactivated vaccine in mice and evaluation of its immunogenicity in pigs.

BACKGROUND: Senecavirus A (SVA) causes an emerging vesicular disease (VD) with clinical symptoms indistinguishable from other vesicular diseases, including vesicular stomatitis (VS), foot-and-mouth disease (FMD), and swine vesicular disease (SVD). Currently, SVA outbreaks have been reported in Canada, the U.S.A, Brazil, Thailand, Vietnam, Colombia, and China. Based on the experience of prevention and control of FMDV, vaccines are the best means to prevent SVA transmission. RESULTS: After preparing an SVA inactivated vaccine (CH-GX-01-2019), we evaluated the immunogenicity of the SVA inactivated vaccine mixed with Imject® Alum (SVA + AL) or Montanide ISA 201 (SVA + 201) adjuvant in mice, as well as the immunogenicity of the SVA inactivated vaccine combined with Montanide ISA 201 adjuvant in post-weaned pigs. The results of the mouse experiment showed that the immune effects in the SVA + 201 group were superior to that in the SVA + AL group. Results from pigs immunized with SVA inactivated vaccine combined with Montanide ISA 201 showed that the immune effects were largely consistent between the SVA-H group (200 µg) and SVA-L group (50 µg); the viral load in tissues and blood was significantly reduced and no clinical symptoms occurred in the vaccinated pigs. CONCLUSIONS: Montanide ISA 201 is a better adjuvant choice than the Imject® Alum adjuvant in the SVA inactivated vaccine preparation, and the CH-GX-01-2019 SVA inactivated vaccine can provide effective protection for pigs.

Electron microscopic observation of Mycobacterium avium subsp. paratuberculosis in cattle feces after a novel purification using liquid paraffin.

We developed a novel method for purifying acid-fast bacteria from feces. The method enabled the observation of characteristic clumps of Mycobacterium avium subsp. paratuberculosis (MAP) under electron microscopy by removing contaminants and other bacteria. Further refinement of this method will contribute to efficient and effective MAP detection.

Emollients in dermatological creams: Early evaluation for tailoring formulation and therapeutic performance.

The targeted choice of the emollient of a cream determines its physicochemical properties and clinical effectiveness. This work researched the effects of emollient properties on the final characteristics and potential performance of oil-in-water dermatological creams. Seven emollients with different chemical characteristics and structures (alkane, triglyceride, ether, silicone, vegetable oils, and mineral oil) were tested in a model formulation. Early stability, pH, droplet size distribution, rheology, tackiness, adhesivity, spreadability, tribology, and release profile of a lipophilic substance model (in Franz cells, through a synthetic membrane, for six hours) were assessed. The creams had acid epicutaneous pH and a "shear-thinning" "solid-like" viscoelastic behavior. Among the seven emollients' properties, polarity, density, and viscosity were the most influential. Droplet parameters were the most impacted, pH and release were moderately affected, and the textural properties were lowly to moderately impacted. The emollient substitution in the model formulation affected the experimental parameters differently, allowing formulation optimization and tailoring its potential therapeutic performance regarding drug release, coadjutant effects, and dwell time on the skin. By looking at the creams' characteristics, it was possible to select the best-suited emollients for releasing a lipophilic drug, applying on painful skin, and formulation in wash-off products or leave-on protective barrier creams.

Can humans smell tastants?

Although studies have shown that olfaction may contribute to the perception of tastant, literature is scarce or circumstantial, especially in humans. This study aims to (i) explore whether humans can perceive solutions of basic prototypical tastants through orthonasal and retronasal olfaction and (ii) to examine what volatile odor compounds (VOCs) underlie this ability. Solutions of 5 basic tastants (sucrose, sodium chloride, citric acid, monosodium glutamate [MSG], quinine) dissolved in water, and 2 fatty acids (oleic and linoleic acid) dissolved in mineral oil were prepared. Triangle discrimination tests were performed (n = 41 in duplicate) to assess whether the tastant solutions can be distinguished from blanks (solvents) through ortho- and retronasal olfaction. Participants were able to distinguish all tastant solutions from blank through orthonasal olfaction. Only sucrose, sodium chloride, oleic acid, and linoleic acid were distinguished from blank by retronasal olfaction. Ethyl dichloroacetate, methylene chloride, and/or acetone were identified in the headspace of sucrose, MSG, and quinine solutions but not in the headspace of water, sodium chloride, and citric acid solutions. Fat oxidation compounds such as alcohols and aldehydes were detected in the headspace of the oleic and linoleic acid solutions but not the mineral oil. We conclude that prototypical tastant solutions can be discriminated from water and fatty acid solutions from mineral oil through orthonasal olfaction. Differences in the volatile headspace composition between blanks and tastant solutions may have facilitated the olfactory discrimination. These findings can have methodological implications for future studies assessing gustatory perception using these prototypical taste compounds.

Characterization of oviduct epithelial spheroids for the study of embryo-maternal communication in cattle.

Most in vitro models of oviduct epithelial cells (OEC) used thus far to gain insights into embryo-maternal communication induce cell dedifferentiation or are technically challenging. Moreover, although the presence of developing embryos has been shown to alter gene expression in OEC, the effect of embryos on OEC physiology remains largely unknown. Here, we propose a model based on bovine oviduct epithelial spheroids (OES) with specific shape and diameter (100-200 µm) criteria. The aims of this study were to i) determine the appropriate culture conditions of bovine OES cultured in suspension by evaluating their morphology, total cell number, viability, and activity of ciliated cells; ii) monitor gene expression in OES at the time of their formation (day 0) and over the 10 days of culture; and iii) test whether the vicinity of developing embryos affects OES quality criteria. On day 10, the proportions of vesicle-shaped OES (V-OES) were higher in M199/500 (500 µl of HEPES-buffered TCM-199) and synthetic oviduct fluid (SOF)/25 (25-µL droplet of SOF medium under mineral oil) than in M199/25 (25-µL droplet of M199 under mineral oil). The proportion of viable cells in V-OES was not affected by culture conditions and remained high (>80%) through day 10. The total number of cells per V-OES decreased over time except in SOF/25, while the proportions of ciliated cells increased over time in M199/500 but decreased in M199/25 and SOF/25. The movement amplitude of OES in suspension decreased over time under all culture conditions. Moreover, the gene expression of ANXA1, ESR1, HSPA8, and HSPA1A in OES remained stable during culture, while that of PGR and OVGP1 decreased from day 0 to day 10. Last, the co-culture of developing embryos with OES in SOF/25 increased the rates of blastocysts on days 7 and 8 compared to embryos cultured alone, and increased the proportion of V-OES compared to OES cultured alone. In conclusion, M199/500 and SOF/25 provided the optimal conditions for the long-time culture of OES. The supporting effect of OES on embryo development and of developing embryos on OES morphology was evidenced for the first time. Altogether, these results point OES as an easy-to-use, standardizable, and physiological model to study embryo-maternal interactions in cattle.

Advanced separation of mineral oil aromatic hydrocarbons by number of aromatic rings using donor-acceptor-complex chromatography to extend on-line coupled liquid chromatography-gas chromatography.

An automated implementation for a subfractionation of mineral oil aromatic hydrocarbons (MOAH) into a mono-/di-aromatic fraction (MDAF) and a tri-/poly-aromatic fraction (TPAF) is presented, which is highly demanded by the European Food Safety Authority (EFSA) respecting the genotoxic and carcinogenic potential of MOAH. For this, donor-acceptor-complex chromatography (DACC) was used as a selective stationary phase to extend the conventional instrumental setup for the analysis of mineral oil hydrocarbons via on-line coupled liquid chromatography-gas chromatography-flame ionization detection (LC-GC-FID). A set of six new internal standards was introduced for the verification of the MOAH fractionation and a quantification of MDAF and TPAF, respectively. The automated DACC approach was applied to representative petrochemical references as well as to food samples, such as rice and infant formula, generally showing well conformity with results obtained by state-of-the-art analysis using two-dimensional GC (GCxGC). Relative deviations of DACC/LC-GC-FID compared to GCxGC-FID methods regarding the ≥ 3 ring MOAH content ranged between -50 and +6 % (median: -2 %, all samples, only values above limit of quantification). However, crucial deviations mainly result from "border-crossing" substances, e.g., dibenzothiophenes or partially hydrogenated MOAH. These substances can cause overestimations of ≥ 3 ring MOAH fraction during GCxGC analysis due to co-elution, which is mostly avoided using the DACC approach. Furthermore, the DACC approach can help to minimize underestimations of toxicologically relevant ≥ 3 ring MOAH caused by an unavoidable loss of MOAH during epoxidation, since natural olefins, such as terpenes, predominantly elute in MDAF, which was exemplarily shown for an olive oil and a terpene reference. The presented approach can be implemented easily in existing LC-GC-FID setup for an automated and advanced screening of MOAH to lower the need for elaborate GCxGC analysis also in routine environments.

Efficiency of natural oils as alternative adjuvants to mineral oils in inactivated avian influenza vaccine formulation.

1. The effectiveness of inactivated vaccines depends on selecting the suitable adjuvant for vaccine formulation. The potency of vaccines with low antigen content can be improved with the appropriate adjuvant. This could allow production of more doses and lower the production cost.2. This study evaluated the efficiency of vaccines prepared using oil extracted from natural sources including argan oil, almond oil, sesame seed oil, pumpkin oil, cactus oil and black seed oil as alternative adjuvants for improving the protection capacity of inactivated influenza virus vaccine as compared to commonly used mineral oils.3. Each vaccine formulation was evaluated for stability, safety and immunogenicity in chickens, as well as for reducing the viral shedding after challenge infection.4. The cactus, sesame and pumpkin seed oil-based vaccines were found to be potent and successfully induced the production of humoral immunity in vaccinated chickens.

Prediction of size-selective permitted daily exposures for mineral oil mist based on an in vitro study in different scenarios.

The incidence of DNA damage from exposure to specific types of metalworking fluids has been reported. In this research, size-selective permissible limits to prevent genotoxic damage in A549 cell lines exposed to two types of mineral oil were estimated for the first time using a benchmark dose approach and extrapolated to workers. The comet assay was performed based on Olive and Banath protocol to determine DNA damage. Then, the Benchmark Dose, the 95% lower bound confidence limit BMD, and the 95% upper-bound confidence limit BMD were determined using continuous response data. Finally, the four Benchmark Dose levels reported in the A549 cell line were extrapolated to the human population in occupational settings in two phases. This study showed when determining the permissible limits, the type used or unused, the type of injury, the organ affected in the body and the size of the particles should also be considered.

Liquid concrete as a gastrointestinal tract foreign body.

Gastrointestinal foreign bodies present a common clinical challenge. We present an unusual case of a 58-year-old construction worker who ingested liquid concrete that risked solidifying in his stomach. Gastroscopy revealed only partial solidification and pyloric obstruction, which were successfully resolved through endoscopic fragmentation and mechanical removal. To protect the gastric mucosa during elimination, liquid paraffin and a cellulose-based formula were administered. Complete gastrointestinal evacuation was achieved within 3 days, with no complications observed. This case emphasises the urgency of the early removal of concrete.

Lessons from Carl M. Pearson 1919 - 1981.

Carl M. Pearson was an energetic and exceptional physician-scholar-leader who founded, established, and broadened the Divisions of Rheumatology at University of California in Los Angeles (UCLA) beginning in 1956. His studies to induce myositis by injecting muscle saturated with the heat-killed tubercle bacillus, an emulsifier, and mineral oil (Freund's adjuvant) enabled his report that polyarthritis occurred with Freund's adjuvant alone in certain strains of rat and mice. This model of adjuvant arthritis allowed the next generation of studies to assess therapies for autoimmune diseases.

[Application of a new-type of defecator in the treatment of rectal fecal impaction].

Objective: This study aimed to investigate the viability and safety of a novel defecator in managing rectal fecal impaction. Methods: In a descriptive case series, this new defecator was administered to constipated individuals among the ages of 18 and 80 years who met the diagnostic criteria for rectal fecal impaction and were identified with acute rectal fecal impaction through CT scans. The contraindications for this defecator included: (1) Anal stenosis, acute intestinal obstruction, and intestinal perforation; (2) Concomitant rectal malignant tumors; (3) Coagulation dysfunction, low platelet counts, gastrointestinal bleeding, or other bleeding risks; (4) Patients with severe underlying conditions affecting the heart, brain, lungs, or other systems; (5) Individuals with mental health disorders. Based on these criteria, clinical data from 42 patients with rectal fecal impaction who underwent treatment with the new defecator at Deyang People's Hospital between July 2020 and April 2023 were retrospectively analyzed.The defecator comprises three components: a head, a spiral rod, and a handle, constructed from disposable stainless steel wire. The treatment procedure involves the following steps: The patient assumes a flexed, supine position on their left side with their buttocks slightly protruding from the bed's edge. A transparent sealing bag is affixed to the buttocks, centered around the anus. With gloved hands inserted through the bag's entrance, a cotton ball soaked in liquid paraffin lubricates the anal canal and the head of the defecator's spiral rod. The defecator is then slowly rotated and inserted into the anus, with careful attention to any changes in resistance. Once the spiral rod is fully inserted, the patient is instructed to inhale and defecate while the defecator is slowly withdrawn, carrying the dislodged fecal matter, and depositing it into the sealed bag. This operation is repeated 2 to 3 times, followed by the injection of either 100 ml of 36°C normal saline or 60 ml of liquid paraffin into the rectum. After a 5 to 8-minute wait, the patient assumes a squatting position to expel any remaining feces from the rectum. The study assessed the operation time, single treatment success rate, pain levels during treatment, and the occurrence of complications. Results: All 42 patients successfully underwent treatment with the new defecator device, achieving a single treatment success rate of 100%. The average operation time was 11.0 minutes (range: 9.0 to 13.3 minutes). During treatment, 20 cases (47.6%) reported moderate to severe anal pain, with 1 case (2.4%) experiencing anal fissure bleeding, and 6 cases (14.3%) reporting discomfort such as palpitations and sweating. No serious complications, including rectal perforation, were observed in any case. Conclusion: The new defecator device demonstrates ease of use and safety, making it a feasible option for treating acute rectal fecal impaction.

Native fungi from Amazon with potential for control of Aedes aegypti L. (Diptera: Culicidae).

Aedes aegypti L. (Diptera: Culicidae) is the main transmitter of pathogens that cause human diseases, including dengue, chikungunya, zika and yellow fever. Faced with this problem, this study aims to select fungi with entomopathogenic potential against Ae. aegypti and develop formulations that optimize the control action of entomopathogenic fungi in the semi-field condition. 23 fungal strains native from Amazon were inoculated in Potato-Dextrose-Agar (PDA) culture medium for 14 days and then transferred by scraping to tubes containing 0.9% NaCl solution. To obtain the larvae, eggs were collected using traps in peridomestic environments for 7 days. 20 larvae of Ae. aegypti in 125 mL erlenmeyers containing 20 mL of conidial suspension at a concentration of 1x106 conidia/mL for initial selection and 1×104, 1×105, 1×106 and 1×107 conidia/mL for determination of LC50. Mortality was checked every 24 h for 5 days. The three fungi with the best virulence rates were identified using molecular techniques. The compatibility between fungi at a concentration of 1×106 conidia/mL and oily adjuvants, mineral oil and vegetable oil (andiroba, chestnut and copaiba) at concentrations of 0.1, 0.5 and 1% was evaluated. The germination capacity of 100 conidia per treatment was evaluated after incubation at 28 ºC for 24 h. To evaluate the entomopathogenic potential of the fungal formulations, conidial suspensions (1×106 conidia/mL) were added with 0.1% mineral and vegetable oil. The treatments were submitted to laboratory and semi-field conditions and mortality was verified every 24 h for 5 days. Beauveria sp. (4,458) (LC50 = 8.66× 103), Metarhizium anisopliae (4,420) (LC50 = 5.48×104) and M. anisopliae (4,910) (LC50 = 1.13×105) were significantly more effective in the larval control of Ae. aegypti, in relation to the other fungal morphospecies evaluated. Mineral oil was better compatible in all treatments evaluated. Beauveria sp. (4,458) was considerably less virulent under semi-field conditions. M. anisopliae (4,910) formulated with mineral oil increased larval mortality to 100% on the 4th day in the laboratory and on the 5th day in the semi-field. Fungal formulations developed from native Amazonian isolates represent a promising tool for the development of strategies to control Ae. aegypti.

Occurrence and Formation Mechanism of PCDD/Fs and SCCPs in Chlorinated Paraffin Products.

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and short-chain chlorinated paraffins (SCCPs) can be formed during the production of chlorinated paraffins (CPs). Detection and accurate quantification of PCDD/Fs in CPs are challenging because of their matrix complexity. Therefore, the occurrence and formation mechanisms of PCDD/Fs from CPs have not been studied extensively in the past. In this study, 15 commercial samples including solid and liquid CPs were collected in 2022 from China. The average ΣSCCP concentrations detected in the solid and liquid CPs were 158 and 137 mg/g, respectively. The average International Toxic Equivalent (I-TEQ) values of 2,3,7,8-PCDD/F in solid and liquid CPs were 15.8 pg I-TEQ/g and 15.0 pg I-TEQ/g, respectively. The solid and liquid CPs had different predominant congener groups for SCCPs and PCDD/Fs. Possible formation routes for the generation of PCDD/Fs were analyzed by screening precursors in paraffin and laboratory-scale thermochemical experiments of CPs. The transformation between 2,3,7,8-PCDD/Fs and non-2,3,7,8-PCDD/Fs was recognized by calculating the successive chlorination preference. The first reported occurrence of PCDD/Fs in CP commercial products indicated that exposure to CPs and downstream products might be an assignable source of PCDD/F emission, which is of great significance to further explore the control factors of PCDD/Fs in the whole life cycle of CPs.

Formation and sedimentation of oil-mineral aggregates in the presence of chemical dispersant.

The formation and sedimentation of oil-mineral aggregates (OMAs) is the major method to transport spilled oil to the seafloor. In this study, the formation and sedimentation experiments of OMA using montmorillonite and four crude oils were performed in a wave tank in the presence of chemical dispersant. Most of the formed OMAs were droplet OMAs, and single droplet OMA would aggregate into multiple ones under the action of the dispersant. The size of the oil droplets trapped in the OMA increased with time and was larger for the oil with higher viscosity. The sinking velocities of OMAs formed in this study were between 100-1200 µm s-1 and they were positively correlated with their diameter. The density of OMA was of the same order as that of the crude oil that formed them. An increase in the dispersant dosage could promote the formation of OMAs. The oil content in OMAs was higher for the denser oil in the presence of a dispersant. The maximum oil trapping efficiency of OMAs was 48.05%. This study provides fundamental data on the formation kinetics of OMAs.

Extrinsic lipoid pneumonia due to chronic polyethylene glycol consumption: A case report.

Extrinsic lipoid pneumonia (ELP) results from the aspiration of lipid-containing substances. Tissue or cell histopathology after Oil-Red-O staining can confirm the diagnosis, which requires proper tissue handling and preparation during bronchoscopy. Here, we report a case of ELP in a quadriplegic patient with a long history of dysphagia and polyethylene glycol consumption. Computed tomography (CT) of the chest revealed multiple, progressively enlarging, fat-attenuated, nodular pulmonary lesions. Bronchoscopy with bronchoalveolar lavage (BAL) and a transbronchial forceps biopsy confirmed the diagnosis of lipoid pneumonia. We discuss the clinical, radiological, and pathological features of ELP and highlight the preparatory steps required for obtaining a successful diagnosis.